Not yet rated Add your review
The nova300 utilizes the highly regarded ES9018K2M SABRE32 Reference DAC. The 9018 DAC is capable of accepting an extremely wide range of inputs all the way up to 32-Bit/384kHz PCM & 5.6MHz DSD (double-DSD). Free shipping to continental USA!
The nova300 utilizes the highly regarded ES9018K2M SABRE32 Reference DAC. The 9018 DAC is capable of accepting an extremely wide range of inputs all the way up to 32-Bit/384kHz PCM and 5.6MHz DSD (double-DSD). The DAC exhibits exemplary dynamic range, jitter elimination and low noise characteristics to satisfy even the most demanding listeners.
A New Generation of Power Amplification
The nova300 incorporates the latest generation of ICEPower amplification - with an impressive 300 watts per channel. The amplifier utilizes ICE power’s innovative and patented Hybrid Controlled Oscillation Modulator (HCOM) feedback and control techniques to ensure high output, wide bandwidth, low noise, robust stability and a simplified overall design. HCOM incorporates separate feedback loops after the power stage and after the output filter. This lets the system address specific issues related to the power stage and output filter independently, resulting in lower distortion, less noise on the output, a less load-dependent frequency response, and a very low output impedance compared to other class D amps. This new amplifier technology is extremely powerful, dynamic, quiet and most importantly... musical. Relatively small size and superior efficiency allows a nova chassis that is even smaller than its predecessors, without the large, heavy and expensive heat sinking common in class A/B amplifiers. The amplifier in the nova300 is capable of driving an extremely wide range of speakers with impedances as low as 2.5Ω and as high as 16Ω. Combine that with a power output of 300 watts per channel and you can be sure this new nova will easily drive your favorite loudspeaker.
Where's the TUBE? The tube is GONE?!?
Yes, it is. Because the new nova preamp is just so good! Previous generation Peachtree preamps had a signal to noise ratio in the range of 95 to 100 dB, similar to competing preamps. When our signature tube buffer was engaged to smooth out a rough recording the S/N dropped to 88-90dB, an acceptable compromise for the sonic benefit.
The new amplifier modules in the current generation of nova are inherently warmer sounding than previously, while still retaining the accuracy digital amps have always provided. Combined with a cleaner analog section and no noise created by an internal tube circuit and we're now able to get even closer to the sound of the original musical performance. The newly-designed preamp section in the nova300 has a S/N ratio of 111dBand is a major contributor in getting us closer to that original sound.
So has Peachtree given up on tubes? Not at all. We're planning a proper stereo tube buffer, complete with separate power supply, for the future. This will connect into the LOOP input/output of the nova amplifiers.
Quiet as a Mouse
The nova300 utilizes an extensive power supply and grounding design to ensure the noise floor is pushed as far down as possible to allow the music to shine through. Our engineers spent hours upon hours determining the optimal power supply filtering and grounding scheme to prevent any unwanted noise from finding its way into the signal path. As a result, the nova300 achieves a remarkable dynamic range and signal-to-noise ratio. Turn up the nova300 to full volume without music playing, put your ear to the speaker and enjoy the lack of noise!
iOS Input - Introducing DyNEC (Dynamic Noise Elimination Circuit) for iPhone/iPad
The nova300 includes a dedicated asynchronous USB connection on the rear panel that provides a direct digital wired connection for Apple Lightning-equipped devices. Simply use the cable that came with your iPhone or iPad and enjoy your music transformed by the ESS SABRE32 Reference DAC and the superior sonic performance of the nova!
We know that streaming music files from the Lightning connection on the iPhone or iPad is VERY convenient. Peachtree wants to make sure you achieve MAXIMUM performance from these high-tech marvels!
By its very nature, any computer generates "noise". A computer's power supply is one source of this noise. Years ago we attacked this issue of computer-generated noise by isolating the USB inputs of our amplifiers. Having successfully conquered "conventional" computer noise, we want to be sure you enjoy the same noise-free performance from your iPhone and iPad.*
*Smart phones, notepads and tablets are, of course, small but powerful computers. Power supplies and high-resolution screen refresh rates are possible sources of noise contamination.
With this goal in mind, Peachtree engineers have developed DyNEC: the world's first and only system to address and eliminate all audible power supply and screen noise. DyNEC assures your music files are streamed to the nova free of any added noise - so your favorite music sounds its very, very best!
Once all sources of noise are eliminated, music files are "handed off" to our internal ESS SABRE32 Reference DAC - further improving performance via asynchronous connection, and eliminating any timing errors caused by jitter.
With DyNEC and an asynchronous connection, Peachtree's dedicated iOS input lets you hear your music with all the clarity, dynamics and emotion the artist intended. So can the iPhone and iPad - perhaps the most convenient music playback devices ever - be taken seriously as high-end audio components? Connected to Peachtree's iOS input, our answer is a resounding YES!
And . . . the new metal-faced Peachtree remote controls basic playback functions like FF/RR and pause, so you can just sit back and enjoy! DyNEC is a Peachtree exclusive.
What’s Old is New Again
We are pleased to say that the nova300 includes a moving magnet (MM) phono input for direct connection of a turntable. Yes, that's right - a bunch of computer audio advocates made a phono preamp! And not just any phono input... a custom designed circuit that accommodates a wide range of MM cartridge outputs. With the nova300 you no longer need an external phono preamp unless you are using a lower output moving coil cartridge. In that case, the internal phono preamp in the nova300 can be bypassed, allowing the phono input to accept line-level signals from a dedicated phono preamp or any other line-level device. Win-win!
Home Theater Bypass (HTB) is Back!
This is one of our most requested features and it is included in the nova300! HTB allows for easy integration with a multi-channel preamp/processor or audio/video receiver (AVR) so that the power amplifier in the nova300 drives the front left and right speakers for stereo and multi-channel listening. The nova300 amplifier section is likely more powerful and better sounding than any AVR available today - and relieving the AVR from driving the front left and right speakers makes it MUCH easier for the AVR to drive the center and surround speakers. When listening to stereo music the nova300 becomes your control center, and you can enjoy the full benefit of its reference DAC and ultra-low-noise circuitry. If the HTB input isn't needed it can be configured as a standard analog line-level input.
The nova300 includes an extremely useful LOOP ( output/input ) feature, allowing you to add an external tube buffer, equalizer or other processor into the signal path as desired. The LOOP button on the remote control engages and disengages the loop audio path utilizing high-performance relays. Do you want to experiment with room correction? No problem. Wire your room EQ component into the nova300 and use the LOOP button on the remote control to easily A-B between correction in/correction out.
Power Amp Mode
The nova300 provides a Volume Control Bypass feature on its digital inputs which puts the nova300 into a "power amp" mode. This is particularly useful if you have a connected source with its own volume control. Have a favorite device or app with a volume slider built right into the interface? Simply bypass the nova300 volume control for that input and use the app slider instead. VERY convenient!
Optical, Coax and USB Inputs
The nova300 offers a standard suite of digital audio inputs, including asynchronous USB for a computer. In addition, there is one coaxial S/PDIF input and two optical inputs that accommodate signals up to 24-Bit/192kHz, assuming the connected device can output those signals. If it can't, no worries; use your computer instead to output your high-res files to the nova300's asynchronous USB input.
Discrete Headphone Amp
Headphone fans will love the newly designed HIGH OUTPUT discrete low impedance headphone amplifier in the nova300. It easily drives any headphone on the market - superbly! The signal-to-noise ratio of the circuitry will impress even the most dyed-in-the-wool headphone enthusiast! When you plug headphones in, the speakers and preamp outputs are automatically muted and the volume knob becomes a dedicated headphone volume controller. Unplug the headphones, and the system reverts back to being an integrated amplifier.
Optional Wi-Fi Module
The nova 2.0 platform was designed to accommodate an internal Wi-Fi module, which is currently under development. We have even reserved an input button on the front panel for it! This will allow you to stream audio directly into the nova300 without the need for connecting any wires. Until then, you can easily connect to the world of streaming audio via a Wi-Fi enabled computer or iDevice, Apple TV ( 3rd generation ), SONOS Connect or Google's Chrome-cast Audio ( to name just a few ).
When we set out to reinvent nova, we called on a team of world-class engineers to design a platform that would achieve our simple but lofty objectives: superior performance, more inputs, greater flexibility, wireless capability, smaller size - all this, plus built in North America within the price range of our previous integrated amplifiers. We came together and created nova 2.0: the best sounding, most accommodating and most reliable integrated amplifier platform we have ever built. Listen to the nova300 - we'll let the results speak for themselves!
Made in North America
The nova300 is designed and built in North America. The circuit boards are built, the amplifiers assembled and fully tested, then inspected at an ISO 9001:2008, 13485:2003 ( Medical Devices ) and MFi Certified Facility in Canada. Amplifiers are then shipped to us in North Carolina where the wooden case is installed and the final product inspected again! Building this product in North America was a coordinated team effort and a significant milestone in Peachtree's history. We are extremely proud that the nova300 is designed and built in North America!
|Compatible Speakers||2.5-16 Ω|
|Output Power (WPC, 8 Ω | 4 Ω, <1% THD+N, AES17)||300 | 450|
|Dynamic Range (A-weighted)||105 dB|
|Damping Factor (1 kHz, 8 Ω)||>625|
|Frequency Response (20 - 20 kHz)||<+/-0.4 dB|
|Inter-Modulation Distortion||>80 dB below fundamental|
|Total Harmonic Distortion (AES17, 1 kHz, 4Ω)||0.005%|
|Channel Separation (1 kHz, 8 Ω)||>90 dB|
|Output Voltage (rms)||3.8V|
|Output Impedance||100 Ω|
|Signal-to-Noise Ratio (Analog | Digital Source, un-weighted)||105 dB | 105 dB|
|Channel Separation (1kHz)||>115 dB|
|Frequency Response (Analog | Digital Source, 8Hz-20kHz)||<0.1dB | <0.5dB|
|Total Harmonic Distortion||0.003% (2V rms, 1 kHz, un-weighted)|
|Output Power (32 Ω, rms | peak)||1200 mW | 2770 mW|
|Output Power (300 Ω, rms | peak)||330 mW | 700 mW|
|Output Power (600 Ω, rms | peak)||170 mW | 350 mW|
|Signal-to-Noise Ratio (Analog | Digital Source, un-weighted)||107 dB | 106 dB|
|Dynamic Range (Analog | Digital Source, un-weighted)||107 dB | 100 dB|
|Channel Separation (1 kHz)||>100 dB at 1 kHz|
|Frequency Response (Digital source, 8 Hz-20 kHz)||<0.5dB|
|Frequency Response (Analog source, 8 Hz-100 kHz)||<0.1dB|
|Total Harmonic Distortion||0.003% (2V rms, 1 kHz, un-weighted)|
|Formats||PCM and DSD|
|PCM Sampling Rate and DSD Frequency Rate||16-32 Bit, 44.1-38 4kHz PCM
2.8224-5.6448 MHz DSD
|COAX & OPT inputs|
|Formats||16-24 Bit, 44.1-192 kHz PCM|
|Maximum Voltage (rms | peak-to-peak)||3.5V | 10V|
|Maximum Input Voltage (rms)||120 mV|
|RIAA EQ||No rumble filter used|
|LOOP output and input|
|Maximum Voltage (rms | peak-to-peak)||3.5V | 10V|
|Impedance (input | output)||100 kΩ | 100 Ω|
|AC Input||100-240VAC, 50/60Hz|
|Maximum Power Consumption||1200 watt|
|On Mode (Idle) Power Consumption||32 watt|
|Standby Mode Power Consumption||<0.5W|
|Fuse||100-120VAC: 8A/250V Medium Acting
220-240VAC: 4A/250V Medium Acting
|Height (including feet)||4.37 inches | 111 mm|
|Width||14.02 inches | 356 mm|
|Depth (including volume knob & speaker binding posts)||14.25 inches | 361.95 mm|
|Weight (shipping weight)||17 lbs (21lbs) | 7.7 kg (9.5kg)|
|Parts & Labor||Two years
Three years if registered online
Are you an audiophile on a budget? If you check out via PayPal, you have the option offered at PayPal checkout! (Free to sign-up & free account).
Or contact us to inquire how you can finance your purchase through our partner, (Synchrony).